Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя страница 76

Страница: 76 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

APPENDIX A: Installing Ear Racks on the Z3-MVE-150

For these steps you will need:

▪

The Z3-MVE-150

▪

2 x Ear Rack Brackets

▪

6 x 4 mm (L) x 3 mm (D) screws

▪

Phillips Head Screwdriver

Complete the following instructions to install your Ear Rack Mounts on your Z3-MVE-150:

(1) Place the Z3-MVE-150 face-up on a dry, flat surface.

(2) Place one of the ear rack brackets on the left and one on the right of the Z3-MVE-150 so that the holes
on the unit align with the brackets. The brackets are identical so it does not matter which bracket goes on
which side.

(3) Using the 4 mm (L) x 3 mm (D) screws provided, secure each bracket with your Phillips head screwdriver.

(4) Repeat this step for the opposite side.

Figure 68 Z3-MVE-150 with Ear Racks

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды