Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 15 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(15)

If the encoder hasn’t already autostarted, click on “start” in the “Channel Controls” section near

the bottom of the screen. If the encoder is already running, click on “stop” and then “start” to
confirm the specified values are in effect.

*Note:

By default a limited selection of video encoding settings are available in the user interface. See Section

8.3, “Advanced Settings Mode”, for more information on accessing additional settings.

Figure 6 Channel 1 Tab – UDP

(4) Change to “UDP”

(5) Change to PC IP

Address or
Multicast Address

(6) Note Value

(1) If necessary, click “Stop”

(7) Click “Start”

(2) Verify

Is “HD-SDI”

(3) Change to

“1920x1080” or

“Follow input”

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды