Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 38 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.18

Encoding Closed Captioning

The Z3-MVE-150 supports extraction of closed caption data from SDI input. This automatically occurs any
time SDI input with closed caption data included is used. To utilize this feature, complete the following:

(1)

Connect an SDI signal with closed caption data to the SDI Input (see Section 5.0).

(2)

Configure the encoder to output UDP (See Section 6.4).

(3)

Open the stream in VLC (See Section 6.5).

(4)

In VLC, select “Subtitle – Sub Track – Closed Caption 1”. This configures VLC to use the extracted

closed caption data that the encoder has extracted and encoded. You will then see the subtitles on
the screen.

Figure 37 Setting VLC to use the Extracted Closed Caption Data

(1) Select “Subtitle – Sub Track – Closed Caption 1”

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды