Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 27 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.11

Changing the Bitrate and Frame Rate Dynamically

The Z3-MVE-150 includes an “update” button which allows you to change the bitrate or frame rate
without stopping and restarting the encoder. To observe this feature, complete the following steps:

(1)

In VLC, click on “Tools” and select “Codec Information”. This brings up a window with four tabs.

Select the “Statistics” tab. In this tab, you can see the current video + audio bitrate:

(2)

In the CH1 tab, change the “Video Bitrate” from “8000K” to “2000K” and click the “update” button.

Figure 22 Changing the Bitrate Dynamically

(1) Change bitrate to 2000K

(2) Click “update”

Figure 21 Viewing Bitrate in VLC

video + audio bitrate

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды