Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя страница 61

Страница: 61 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

9.2

The User Presets Tab

Parameter

Notes

new

Define a new configuration file. Up to nine configurations can be created.

rename

Rename a configuration file.

delete

Delete a configuration file.

export

Export current settings to a file. All presets get saved to the file “settings.z3” on
the host PC. These can be subsequently reloaded with the “import” command.

import

Load settings from a previously exported file.

reset

All existing user presets will be erased.

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды