Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 26 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.10

Encoding an HDMI Video Source

The Z3-DME-10 also supports encoding non-HDCP HDMI video.

Connect an HDMI source to “HDMI In” on the rear panel of the encoder.

Return to the user interface and click the “stop” button to stop any current encoding.

At the CH1 tab, change the “Video Source” to “HDMI1” using the dropdown menu.

Verify your remaining settings are as desired. See Section 9.0 for a detailed list of all options.

*Note:

By default a limited selection of video encoding settings are available in the user interface. See Section

8.3, “Advanced Settings Mode”, for more information on accessing additional settings.

Click the “start” button.

Figure 20 Channel 1 Tab - HDMI

Figure 19 Z3-MVE-150 Rear Panel HDMI Encode Connections

(1) Change to

“HDMI1”

(2) Click “Start”

(1) Connect to

HDMI Source

(2) Connect to

Ethernet

(3) Connect to

AC Power

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды