Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя | Manualshive

Страница: 58 / 79

background image

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

58

9.0

SUMMARY OF OPTIONS

This section lists the different options that are available in the various menus.

9.1

The System Setup Tab

Parameter

Options (default in bold)

Notes

Local IP Setup

Local IP Address

192.168.x.y

(192.168.81.68)

Sets the IP address of the Z3-MVE-150. Note that
a “save” of these settings and a reboot is
needed for changes to this value to take effect.

When in DHCP mode, this field is not applicable.

Local Netmask

255.255.z.w (

255.255.0.0

)

Sets the netmask of the Z3-MVE-150. Note that a
“save” of these settings and a reboot is needed
for changes to this value to take effect.

When in DHCP mode, this field is not applicable.

Default Gateway

192.168.a.b (

192.168.0.1

)

Sets the network gateway to use for the Z3-MVE-
150. Note that a “save” of these settings and
reboot is needed for changes to take effect.

When in DHCP mode, this field is not applicable.

DNS Server IP 1

a.b.c.d (8.8.8.8)

Specifies the primary DNS server to be used for
hostname lookup when in static IP mode. When
in DHCP mode, DNS information is acquired from
the DHCP server and this field is not applicable.

DNS Server IP 2

e.f.g.h (8.8.4.4)

Specifies the secondary DNS server to be used
for hostname lookup when in static IP mode.
When in DHCP mode, DNS information is
acquired from the DHCP server and this field is
not applicable.

Device Setup

Use DHCP

Checked

Unchecked

Sets whether DHCP is used to dynamically obtain
an IP address at start up.

Auto Start

Checked

Unchecked

Check this box to set the system to
automatically start encoding upon powering on.

«
...
56
57
58
59
60
...
»

Содержание EUS Z3-MVE-150
















































































Отзывы:

Нет отзывов

Похожие инструкции для EUS Z3-MVE-150

Бренд: XSY Страницы: 22

Бренд: Y-Solar Страницы: 5

Бренд: Panasonic Страницы: 2

Бренд: Cambridge Audio Страницы: 4

Бренд: Cambridge Audio Страницы: 2

Бренд: Caliber Страницы: 26

Бренд: D-Link Страницы: 6

SOLECTRIA XGI 1500 Series

Бренд: YASKAWA Страницы: 70

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 118

VARISPEED-616G5

Бренд: YASKAWA Страницы: 355

Бренд: OT Systems Страницы: 16

Бренд: Net Optics Страницы: 15

Бренд: Planet Страницы: 32

Бренд: GALAGAR Страницы: 28

Бренд: SAJ Страницы: 32

EdgeVis HD-IP200

Бренд: Digital Barriers Страницы: 34

Бренд: Senci Страницы: 39

WIEGAND-Ethernet

Бренд: S4A Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды