Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 79

background image

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

59

Advanced Settings

Checked

Unchecked

Check this box for advanced encode settings to
appear on the channel tab.

Device Management

Set Device Name

Sets a custom name for the unit to appear in the
user interface and ZFinder.

Set Password

Sets a password to limit access to the user
interface.

Update device firmware Button

Access the Software Updater to update the
firmware on your device. An image file of the
desired firmware is needed.

Download device logs Button

Extract a set of diagnostic logs that can be
provided to Z3 in the event of an issue to be
reported. The resulting file is saved on the PC
with the user interface open.

View logs Button

Can be used to view system logs. Used by Z3 for
debugging.

Reboot Button

Restarts the unit without the need to disconnect
power.

Display Mode

(Decode Only)

SDI

HDMI

HDMI and SDI output are supported.

Resolution

(Decode Only)

1080p60

Sets the resolution to set the display to.

[Note

1]

Layout

(Decode Only)

1x1

Determines layout to use for displaying multiple
pictures. In most cases 1x1 is used. 2x2 can be
used when four decodes are occurring. Other
configurations are possible.

[Note 2]

Set Display Button

(Decode Only)

If a display mode, resolution, or layout different
from the default is desired, the user would
change to the desired value and then click the
“Set Display” button.

Note 1:

Resolutions supported:

«
...
57
58
59
60
61
...
»

Содержание EUS Z3-MVE-150
















































































Отзывы:

Нет отзывов

Похожие инструкции для EUS Z3-MVE-150

Бренд: 3onedata Страницы: 3

Бренд: Gama Sonic Страницы: 4

Бренд: INTECNO Страницы: 16

Бренд: Redgum Страницы: 12

Бренд: Schumacher Страницы: 45

Бренд: Tripp Lite Страницы: 4

Бренд: Potek Страницы: 18

Бренд: B&B Electronics Страницы: 2

Бренд: CEL-MAR Страницы: 16

Бренд: Optical Systems Страницы: 2

ICT206012-100AI2

Бренд: ICT Страницы: 2

Popcorn Hour A-410

Бренд: Syabas Technology Страницы: 95

Бренд: Must Страницы: 10

climatronic converter WMS UP

Бренд: WAREMA Страницы: 4

EXT-DVIDL-2-HDMIR

Бренд: Gefen Страницы: 14

Бренд: GPX Страницы: 2

Tsunami TSU-AT1000

Бренд: SoundTraxx Страницы: 6

Бренд: Baudcom Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды