Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя страница 68

Страница: 68 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Z3 for optional upgrade information.

Aux TS File Enable

(UDP, TSRTP, MPTS

& ASI Only)

True

False

Set to True to allow the same UDP or TSRTP
stream to be saved to a .ts file.

Output Device

(Aux TS File

TSFILE Only)

No Storage Devices Found

/dev/sda1

/dev/sdb1

Click this field to select the USB storage
device for .ts file destination. IT auto-
populates based on storage devices
detected.

If one USB device is connected, “/dev/sda1”
corresponds to either port.

If two USB devices are connected,
“/dev/sda1” corresponds to USB device that
was connected first and “/dev/sdb1”
corresponds to the USB device that was
connected second.

Only one of the two USB ports can be
selected at a time.

File Prefix

(Aux TS File

TSFILE Only)

MOV

Textbox to enter desired file name for .ts
file. Entered text will be followed by a
number starting with zero in the recorded
file name.

Eject Button

(Aux TS File

TSFILE Only)

(up arrow icon)

Click to eject the USB when finished
recording.

Dest Address

(For all but MPTS &
ASI)

x.y.z.w

(225.1.2.3)

IP address that the encoder is streaming to.

Dest Port

(For all but FILE,
MPTS & ASI)

0 – 9999 (

5004

)

The port that the encoder is streaming to.

Video PID

(UDP, TSFILE, MPTS

& ASI Only)

0 – 999 (

221

)

PID assigned to video in the TS stream.

PCR PID

0 – 999 (

521

)

PID assigned to PCR in the TS stream.

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды