Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 46 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(11)

Navigate to the CH1 tab and, if audio is needed, select “HDMI” from the “Output Port” dropdown

menu.

(12)

Click the “start” button to begin decoding. Video will appear on the monitor after 5-10 seconds.

7.6

Output SDI

(1)

Connect a BNC cable from “SDI Out” on the decoder unit to an HD TV or monitor.

(2)

Return to the user interface System Setup tab. In decoder mode, settings for Display Setup appear.

(3)

Select “sdi” for the “Display Mode” using the dropdown menu.

(4)

Verify the “Resolution” and “Layout” are as desired and click the “Set Display” button.

Figure 49 Set Audio for HDMI Output

) Set to “HDMI”

) Click “start”

Figure 50 Z3-MVE-150 SDI Output Connection for Decode

SDI

Out

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды