Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 13 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.3

Find the Encoder Using ZFinder

ZFinder is a PC Utility that allows you to find any Z3 Technology product on your network. If you have
not downloaded this to your computer, you can find it on the USB drive provided with your system.

(5)

Verify your PC is set to DHCP. If it is set to a static IP address, ZFinder will be unable to discover your

encoder, or it will appear in red and you will be unable to proceed further.

(6)

Run the “ZFinder” PC Utility on your Windows PC. The ZFinder window appears. ZFinder then

completes a scan of the network and lists the location of all Z3 systems connected to the network.
In this case, the Z3-MVE-150 appears.

(7)

Click on the Z3-MVE-150 entry in the window to select it. This will cause the “Edit Device”, “Open

Device” and “Flash LEDs” boxes to activate.

*Note:

Selecting “Edit Device” allows for manual changes to network settings. Selecting “Flash LED’s” is not

applicable to the Z3-MVE-150 as there are no LEDs.

(8)

Click on “Open Device.” An Internet browser window is opened (for best results, Firefox or Chrome

are recommended) and the HTTP-based graphical user interface (GUI) appears at the System Setup
tab.

Figure 4

ZFinder with a Product Selected

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды