Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 42 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

7.2

Decoding ASI Input

(1)

The SDI connections also support ASI. Connect a BNC cable from your video encoder or other device

streaming encoded ASI content to “SDI In” on the decoder unit.

(2)

Return to the user interface “CH1” tab.

(3)

Set the “Input Interface” to “ASI” using the dropdown menu.

(4)

If desired, set “Audio Output” to “ON” using the dropdown menu to allow for audio with the decoded

video.

(1) Connect to

ASI Input

Figure 42 Z3-MVE-250 Rear Panel ASI Decode Connection

Figure 43 Channel 1 Tab – ASI Decode

(1) Change to “ASI”

(4) Set Audio Output to “ON”

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды