YASKAWA MOTOMAN FS100 Скачать руководство пользователя страница 343

Страница: 343 / 348

11-5

159645-1CD

RE-CHO-A111

11 LED Indicator on Each Circuit Board
11.2 7-Segment LED Indicator on the Main CPU Circuit Board (CPU201R)

FS100

11.2.2 Status of 7-Segment LED Indicator at Control Power Start-up (one digit)

11.2.3 Status of 7-Segment LED Indicator at Hardware Error Occurrence

When the hardware error is detected during the operation, the error is
indicated with 4-digit numbers with the letter [H] at its head.

Indication spec.:

Repeat of [ H ]

→

[0]

→

[0]

→

[0]

→

[1]

→

[.]

Turn the power supply OFF and ON again when the above mentiond
numbered error is indicated by the 7-Segment.

Replacement of the controller is requied if the the error occurs again.

Error Status

The system program has started.

Starts verifying the existence of other circuit boards.
(Verifies the start-up of the booting program.)

Starts the system program transmission.

Sends the request of the system program start-up.

Starts verifying the existence of other circuit boards.
(Verifies the start-up of the system program.)

Acquires hardware information, etc. of other circuit boards.
(Verifies the IO board status, SERVO IF, and so on.)

Starts the CMOS data transmission.

Sends the pre-online request.

Waits for MIII communication synchronization.

A
b

Sends the start-up request of on-line system.

The on-line system has started. (Starts up the initialization task.)

Processes of the system setup completion. (Servo ON enabled)

Alarm occurs at the system setup.

The maintenance mode is starting up.

The system setup PP/SWP unconnected.

Alarm No.

H0001

MAC address eorror

H0002

Power lost error when start-up

H0003

Watchdog error when start-up

H0004

Interrupt clear impossible

H0005

Initialization of SERVO communication
error

343 of 348

Содержание MOTOMAN FS100





























































































































































































































































































































































Результаты поиска

Содержание MOTOMAN FS100

Отзывы:

Похожие инструкции для MOTOMAN FS100

Бренды по названию

Популярные бренды

YASKAWA MOTOMAN FS100, Руководство по обслуживанию

Результаты поиска

Содержание MOTOMAN FS100

Отзывы:

Похожие инструкции для MOTOMAN FS100

Бренды по названию

Популярные бренды