YASKAWA MOTOMAN FS100 Скачать руководство пользователя страница 297

Страница: 297 / 348

9-195

15964

5-1CD

RE-CHO-A1

FS
10

4670

INSUFFICIENT NUM OF
SAMPLE DATA

Sub Code: Signifies the axis in

which the alarm occurred

Setting error

Lengthen the measurement section.

4671

SAMPLE BUFFER OVER
FLOW

Sub Code: Signifies the axis in

which the alarm occurred

Setting error

Shorten the measurement section.

4672

BASIC SPEED
UNREACHED

Sub Code: Signifies the axis in

which the alarm occurred

Setting error

Increase the speed specification value of a measurement job or set a small

value for BASICV.

Or set a small value for BASICT, or lengthen the measurement section.

4673

MAX TRQ
UNDETECTED

Sub Code: Signifies the axis in

which the alarm occurred

Setting error

Set a large value for the BASICT, and then check again.

4676

BROKEN FAN FUSE

Sub Code: Signifies the YSU unit

number in which the alarm

occurred

Connection failure

(1)Reset the alarm.

(2)If the alarm occurs again, check if there is a ground fault or short circuit in the

fan power line.

Fuse failure

(After cancellation of the short-circuit and ground fault) Replace the fuse.

4677

IMPOSSIBLE LINEAR
MOTION

Sub Code: Control group and axis Setting error

(1)Check the following settings.

·If the sub code display is L- and U-axes, perform the teaching again to make

the form (arm folded direction) of L- and U-axes same at start point and end

point.

·If the sub code display is S- and L-axes, perform the teaching again to make

the form (arm folded direction) of S- and L-axes same at start point and end

point.

·Change the teaching move instruction to MOVJ instruction. *Be carefull to the

interefernces with peripheral environment, because the robot changes its

motion.

4681

OVER SPEED
(MainCPU)

Sub Code: Control group and axis Setting error

(1)Check the following settings.
·Reduce the speed of the step where the alarm occurred.
·Change the move instruction to joint interpolation (MOVJ).
* Be careful to the peripheral interference since its movement changes.

4682

MOTION RANGE LIMIT
INTERFERENCE

Sub Code: Manipulator number

Setting error

(1)Check the following settings.

·Modify the teaching position or widen the operation area so that the robot

would not interfere with the operation area.

·Confirm the setting of the robot tool mode (tool interference file) which the

control group is indicated.

4683

AXIS MOTION RANGE
LIMIT OVER(MIN./MAX.)

Sub Code: Control group and axis Setting error

(1)Check the following settings.

·Modify the teaching position or widen the operation area so that the robot

would not interfere with the operation area.

·Confirm the setting of the operation area which the control group is indicated

by the sub code.

4684

INTERPOLATION
INVALID

Sub Code: Control group

Setting error

(1)Check the following settings.

·At the cartesian jog operation, switch to each-axes jog operations, and then

change the orientation of manipulator.

·Change the teaching position and orientation.

Alarm
Number

Alarm Name

Sub
Code

Meaning

Cause

Remedy

297 of 348

Содержание MOTOMAN FS100





























































































































































































































































































































































Результаты поиска

Содержание MOTOMAN FS100

Отзывы:

Похожие инструкции для MOTOMAN FS100

Бренды по названию

Популярные бренды

YASKAWA MOTOMAN FS100, Руководство по обслуживанию

Результаты поиска

Содержание MOTOMAN FS100

Отзывы:

Похожие инструкции для MOTOMAN FS100

Бренды по названию

Популярные бренды