manualshive.com logo in svg

WITTUR iAStar AS380, Руководство пользователя

Поделиться
Скачать
WITTUR iAStar AS380 Скачать руководство пользователя страница 5

Manual-overview of system

2.Overview of system

SmartCom is a modern, on newest technology based control system
especially for elevators.
The system consists basicly on compnents as follows:

•

Control circuit terminal iAStar AS380 with integrated frequency
converter

•

car controller panel SM02G 

•

command board SM03 panel for keys

•

Car top control board SM02H 

•

Display& control board SM04 

•

Extension board SM09

Different variations from each of the the panels/ boards enables an
otimal match between the control system and the elevator in the
required range.
Simple or complex controls based on the always consistent CAN-
records could be implemented.
All components are combinable and extensible  due to the CAN-
system .

Integrated frequency converter iAStar AS380

This  modul optionally in the shaft or outside consists of the frequency converter and the central unit
SM01 of the elevator control. It includes all functions, especially the drive control, detection of car-
position and a lot of special functions, which are normally allocated in the shaft or engine room.
It communicates via the CAN-Bus with the other modules.

Car controller panel SM02

All functions which are related to the cabin are realised by the car controller panel . It  is connected 
via CAN-bus with the control circuit terminal.
There are two variations. The „classic“ which only one  SM02/03, and now with the 32bit board 
F5021  established fragmented variation. In this case there is integrated one SM02/H in car top 
control panel and one  SM02/G  the car controller panel. Thus the 36-pole cable is reduced to a 12-
pole control casble between the car top panel and the car controller panel. The connection from up 
to three additional car controller panels/ console panel is now very easy via CAN-bus.

Command board panel SM03

This board is connected to the car controller panel. Up to 8 panels can be connected to an SM02. 
One command board provides 8 inputs & 8 outputs for the related confirmations.

Display & control board SM04

Those boards could somehow used as floor-display in the cabin or other as floor display for each 
floor with indication of floornumber and continuing indicator.

Seite 3

Содержание iAStar AS380







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды