WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 27

Страница: 27 / 130

WAGO I/O System 750 XTR

Device Description 27

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Table 12: Technical Data – Measured Values

Fundamental vibration/upper harmonic

Current 240 ms

Voltage 240 ms

HD/THD, current 240 ms

HD/THD, voltage 240 ms

Initialization times:

Collection changes

Collection 010 approx. 1400 ms

Collections 020, 021 and 022 approx. 1100 ms

Settling times:

Voltages and currents

620 ms at 100

(1300 ms after power-on)

Active power and apparent power

415 ms at 60 %

915 ms at 100 %

Reactive power

715 ms at 60 %

1215 ms at 100 %

Harmonic Analysis

790 ms

Do not also ground sensors on the module

All sensors are internally connected to PE on one side (N) and must therefore not

be grounded on the module side, as otherwise ground loops can form.

Signal line shielding must be grounded on one side on the side of the sensors.

The settling time is the time in which the measured value has increased from 0 to the value specified in percent

of the full scale.

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды