WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя | Manualshive

Страница: 32 / 130

background image

32 Device Description

WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 56.4 /Serie 750 (WAGO I/O SYSTEM)/Gerätebeschreibung (alte Struktur)/Normen und Richtlinien/EMV-Normen I/O-Modul 750-xxxx/0040-0000, nur Standardversion - Einleitung XTR @ 18\mod_1395909426189_21.docx @ 149708 @ @ 1

The I/O module 750-495/040-010 meets the following EMC standards as these

standards relate to the I/O module:

Pos: 56.5 /Serie 750 (WAGO I/O SYSTEM)/Gerätebeschreibung (alte Struktur)/Normen und Richtlinien/Normen Störfestigkeit XTR (Bundle 1-3) - ohne Schiffbau @ 37\mod_1600765384731_21.docx @ 594609 @ @ 1

Table 20: EMC – Immunity to Interference

Standard

Test Value

Electrostatic Discharge
• EN 61000-4-2

• EN 60255-26

• IEEE C37.90.3

8 kV (contact discharge)

8 kV (air discharge)

High-frequency Electromagnetic Fields
• EN 61000-4-3

• EN 60255-26

• IEEE C37.90.2

20 V/m (80 MHz … 1 GHz)

10 V/m (1 GHz … 3 GHz)

Fast Electrical Transient Disturbances / Burst
• EN 61000-4-4

• EN 60255-26

• IEEE C37.90.1

4 kV

Surge Voltage / Surge
• EN 61000-4-5

• EN 60255-26

2 kV (conductor/conductor)

4 kV (conductor/ground)

Conducted Disturbances, Induced by High-frequency Fields
• EN 61000-4-6

• EN 60255-26

10 V (150 kHz … 80 MHz)

Magnetic Fields With Electrical Frequencies
• EN 61000-4-8

• EN 60255-26

300 A/m continuous / 1000 A/m for 1 s

Pulse-shaped Magnetic Fields
• EN 61000-4-9

300 A/m

Damped Oscillatory Magnetic Fields
• EN 61000-4-10

100 A/m

Voltage Dips, Short-term Interruptions and Voltage Fluctuations
• EN 61000-4-11

• EN 60255-26

Standard not applicable

Damped Sinusoidal Oscillations
• EN 61000-4-12

2 kV (conductor/conductor)

4 kV (conductor/ground)

Harmonics and Interharmonics
• EN 61000-4-13

Standard not applicable

Conducted Asymmetric Disturbances
• EN 61000-4-16

30 V continuous

300 V for 1 s

Line Frequency Disturbances
• EN 60255-26

Class A

(150 V conductor/conductor / 300 V

conductor/ground)

«
...
30
31
32
33
34
...
»

Содержание I/O System 750 XTR 750-495/040-010



































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренд: EAE Страницы: 50

Бренд: Ruida Technology Страницы: 35

EcoZone ConServer

Бренд: IrriGreen Страницы: 29

Weymouth Series

Бренд: Hamworthy Страницы: 28

Бренд: HK Audio Страницы: 105

Бренд: Grundig Страницы: 28

Over-Center 7k51

Бренд: Basta Boatlifts Страницы: 16

Бренд: dB Technologies Страницы: 32

Бренд: Farfisa Страницы: 40

Бренд: hager Страницы: 61

Бренд: Kogan Страницы: 12

ERCOLE QK-E2500

Бренд: Quilo Страницы: 10

Protecta 3590036

Бренд: 3M Страницы: 72

Бренд: Cattron Страницы: 121

Бренд: Johnson Controls Страницы: 4

Бренд: BWT Страницы: 56

Бренд: Hengbida Electronic Technology Страницы: 19

Бренд: morse Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды