WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя

Страница: 35 / 130

WAGO I/O System 750 XTR

Function Description 35

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 58 /Alle Serien (Allgemeine Module)/Überschriften/Ebene 1/Funktionsbeschreibung - Überschrift 1 @ 4\mod_1239025975389_21.docx @ 30003 @ 1 @ 1

Function Description

Pos: 59.1 /Serie 750 (WAGO I/O SYSTEM)/Funktionsbeschreibung/Funktionsbeschreibung 750-0495/040-010 - Messprinzip, Messwerteübersicht @ 35\mod_1561046761367_21.docx @ 548624 @ 222 @ 1

4.1

Measurement Principle

The 3-Phase Power Measurement Module uses six A/D converters to capture the

current and voltage values of all 3 phases according to the schematic illustrations

in the section “Schematic Circuit Diagrams.”

The I/O module can measure periodic signals with a fundamental frequency of

45 Hz to 65 Hz with upper harmonic components up to a frequency of 2 kHz (with

65 Hz line frequency).

The connection for each of the voltage and current sensors for the 3 phases to

the measurement channels is a 2-wire connection.

Low-pass filters on the six inputs have a cutoff frequency of about 16 kHz. Each

input signal is quantized with a depth of 24 bits and processed further digitally.

Acquisition and processing of the measured values of all 3 phases is performed

time-synchronously in an identical manner.

4.2

Measured Value Overview

The 3-Phase Power Measurement Module provides the following measured AC

values for each phase (Lx, Ly = L1, L2 or L3).

Voltage:

• RMS voltage, Lx-N

• Max. RMS voltage, Lx-N

• Min. RMS voltage, Lx-N

• Arithmetic mean, voltage, Lx-N

• Peak value, voltage, Lx-N

• RMS line-to-line voltage, Lx-Ly

Current:

• RMS current, Lx

• Max. RMS current, Lx

• Min. RMS current, Lx

• Arithmetic mean, current, Lx

• Peak value, current Lx

Power:

• Active power Lx

• Maximum active power, Lx

• Minimum active power, Lx

• Reactive power, Lx

• Apparent power, Lx

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды