WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 79

Страница: 79 / 130

WAGO I/O System 750 XTR

Connect Devices 79

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 89 /Serie 750 (WAGO I/O SYSTEM)/Anschließen/Anschlussbeispiele/Analogeingänge/Leistungs-, Spannungs-, Strommessung 750-0495/040-010 @ 35\mod_1561047364614_21.docx @ 548662 @ 2 @ 1

7.4

Measurement of Voltage, Current and Power

Use only standards-compliant sensors, and pay attention to the technical

data

Use only voltage sensors approved per IEC 60044-7 (new version: IEC 61869-7)

and current sensors per IEC 60044-8 (new version: IEC 61869-8), and do so in

accordance with the information in the section “Technical Data.”

Do not confuse the current and voltage connections

When connecting, be sure not to confuse the current and voltage paths. If power

measurements erroneously yield negative power values, check whether you

have connected the corresponding voltage and current sensors in the correct

orientation.

Do not ground sensors

All sensors are internally connected (N) to PE on one side and thus must not be

grounded on the module side, since otherwise ground loops can occur..

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды