WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 105

Страница: 105 / 130

WAGO I/O System 750 XTR

Firmware Update 105

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 98 /Alle Serien (Allgemeine Module)/Überschriften/Ebene 1/Firmware-Update - Überschrift 1 @ 32\mod_1532614793963_21.docx @ 492113 @ 1 @ 1

Firmware Update

Pos: 99 /Serie 750 (WAGO I/O SYSTEM)/Service/Firmware-Änderung/750-495/040-010 - Service - Firmware-Update @ 35\mod_1561047723973_21.docx @ 548694 @ @ 1

You can update the firmware on the Series 750 I/O modules with the “WAGO I/O

Update 750” software. The update of the I/O module is performed via the service

interface. For ETHERNET-based fieldbuses, the fieldbus connection on the

fieldbus coupler/controller is also available.

Please note the following before an update:

•

Ensure that communication with the fieldbus coupler/controller is not

interrupted during the update process.

Damage to I/O module if update interrupted

During the update process, the I/O module must not be removed, and the

power supply must not be interrupted. Otherwise, the I/O module could be

damaged.

•

Close the application on the controller before the update procedure.

•

Before performing an update via the service interface, disconnect the

fieldbus cable from the fieldbus coupler/controller.

•

Only run the “WAGO I/O Update 750” software from a local hard disk.

•

Do not close the “WAGO I/O Update 750” software during the update.

Additional information from WAGO Support

Additional information about the “WAGO I/O Update 750” software is available

from WAGO Support.

Pos: 100 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды