WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 75

Страница: 75 / 130

WAGO I/O System 750 XTR

Connect Devices 75

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 82 /Alle Serien (Allgemeine Module)/Überschriften/Ebene 1/Geräte anschließen - Überschrift 1 @ 3\mod_1234172889468_21.docx @ 27460 @ 1 @ 1

Connect Devices

Pos: 83 /Serie 750 (WAGO I/O SYSTEM)/Anschließen/Schutz vor gefährlichen Berührungsspannungen 750-0495/040-010 @ 35\mod_1561659122511_21.docx @ 549353 @ 2 @ 1

7.1

Protection against Hazardous Touch Voltages

Provide touch-proof protection

Provide all the wiring of the measurement setup with touch-proof protection and

corresponding warning signs.

Use only standards-compliant sensors, and pay attention to the technical

data

Use only voltage sensors approved per IEC 60044-7 (new version: IEC 61869-7)

and current sensors per IEC 60044-8 (new version: IEC 61869-8), and do so in

accordance with the information in the section “Technical Data.”

The 3 voltage measuring paths are not electrically isolated from the

3 current measuring paths

The N connection represents the device-internal reference potential for all

electrical measurements.

Unwanted additional potential differences between the N connection and the

current connections can lead to incorrect measured values and the destruction of

the I/O module.

All N connections of the I/O module must be set to PE in the sensors.

Observe limit values

Ensure that all limit values indicated in the technical data are observed (both

upper and lower limits)! Otherwise, the device could be destroyed.

Observe applicable standards and regulations

During installation, connection and use of the I/O module, observe all relevant

current regional, national and international standards, installation requirements

and accident prevention regulations.

No hazardous voltage occurs on the measurement inputs when the I/O module is

used with appropriate voltage and current sensors according to the

specifications. The voltages on the measurement inputs lie in the range of a few

volts.

However, it is essential to follow the sensor manufacturer’s safety instructions.

Pos: 84 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды