WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 46

Страница: 46 / 130

46 Process Image

WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 61 /Alle Serien (Allgemeine Module)/Überschriften/Ebene 1/Prozessabbild - Überschrift 1 @ 4\mod_1240983067828_21.docx @ 31942 @ 1 @ 1

Process Image

Pos: 62 /Serie 750 (WAGO I/O SYSTEM)/Prozessabbild Lokalbus/AI/Prozessabbild 750-0495/040-010 Teil 1 @ 35\mod_1561046954670_21.docx @ 548639 @ 22332332333 @ 1

The I/O module provides the fieldbus coupler/controller 24 bytes of input and

output process data via one logical channel. This consists of 8-byte control/status

words and 16-byte data words.

The process data image is specific to the fieldbus coupler/controller used

The mapping of the process data is specific to the fieldbus coupler/controller

used. This information, as well as the specific configuration for relevant

control/status bytes, is found in the description of the process image of the

corresponding coupler/controller in the section “Fieldbus-Specific Configuration

of Process Data.”

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды