WAGO I/O System 750 XTR 750-495/040-010 Скачать руководство пользователя страница 21

Страница: 21 / 130

WAGO I/O System 750 XTR

Table of Contents 21

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 40 /Alle Serien (Allgemeine Module)/Überschriften/Ebene 2/Anzeigeelemente - Überschrift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3

Display Elements

Pos: 41 /Serie 750 (WAGO I/O SYSTEM)/Gerätebeschreibung (alte Struktur)/Anzeigeelemente/AI/Anzeigeelemente 750-0495, 750-0495/040-0xx @ 16\mod_1371738731125_21.docx @ 123880 @ @ 1

LED A displays a status message. LEDs B to G display possible error messages.

LED H displays information regarding the rotating field.

Figure 4: Display Elements

The meaning of the indicators is as follows:

Table 6: Legend for Figure “Display Elements”

LED

State

Explanation

Off

Not ready for operation, or

no/faulty local bus communication

Green

Operational readiness and uninterrupted local bus

communication

Note

: If the watchdog has been deactivated, the LED

remains lit (see section “Commissioning” >

“Parameterization with WAGO-I/O-

CHECK”

Off

No error

Red

Group error message for L1:

Under/overvoltage or overcurrent

Off

No error

Red

Group error message: overload of current path IL1, IL2

or IL3 (clipping)

Off

No error

Red

High measurement error, caused by underrun of

nominal input voltage L1, L2 or L3

Off

No error

Red

Group error message for L2:

Under/overvoltage or overcurrent

Off

No error

Red

Group error message for L3:

Under/overvoltage or overcurrent

Off

No error

Red

Group error message: overload of voltage path L1, L2

or L3 (clipping)

Off

Rotating field correct (clockwise, phase sequence: L1–

L2–L3)

Yellow Rotating field incorrect (counterclockwise)

Pos: 42 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание I/O System 750 XTR 750-495/040-010



































































































































Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды

WAGO I/O System 750 XTR 750-495/040-010, Руководство пользователя

Результаты поиска

Содержание I/O System 750 XTR 750-495/040-010

Отзывы:

Похожие инструкции для I/O System 750 XTR 750-495/040-010

Бренды по названию

Популярные бренды