Viconics VT8600 Series Скачать руководство пользователя страница 62

Страница: 62 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

Filter alarm

Window alarm

Off

Service alarm

Fan lock alarm

Off

4/9 Service View

CO2 alarm

Off

Low air alarm

Off

SERVICE VIEW 4/9

PARAMETER DETAILS

Configuration parameters Default Value

Significance and Adjustments

Window alarm

Read Only

Window Alarm

Shows On if there is a Window alarm and shows Off if there is no Window alarm. This
feature is for both wired and wireless sensors.

Display Readings

: On or Off

Service alarm

Read Only

Service Alarm

Shows On if there is a Service alarm and shows Off if there is no Service alarm.

Display Readings

: On or Off

Filter alarm

Read Only

Filter Alarm

Shows On if there is a Filter alarm and shows Off if there is no Filter alarm.

Display Readings

: On or Off

Fan lock alarm

Read Only

Fan Lock Alarm

Shows On if there is a problem detected on the Fan.

Display Readings

: On or Off

alarm

Read Only

Alarm

Shows On if the CO

level (local, wired or wireless) is higher than the “Max CO

”

setpoint.

Display Readings

: On or Off

Low air alarm

Read Only

Low Air Alarm

Shows if the fresh air flow is lower than the “min fresh air” setpoint.

Display Readings

: On or Off

Содержание VT8600 Series

































































































Результаты поиска

Содержание VT8600 Series

Отзывы:

Похожие инструкции для VT8600 Series

Бренды по названию

Популярные бренды

Viconics VT8600 Series, Руководство пользователя интерфейса

Результаты поиска

Содержание VT8600 Series

Отзывы:

Похожие инструкции для VT8600 Series

Бренды по названию

Популярные бренды