Viconics VT8600 Series Скачать руководство пользователя страница 29

Страница: 29 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

2/11 Configuration

Fan delay

Standby mode

Absolute

Standby diff.

2.0 °F

Fan cont. heat

Power-up delay

10 Sec.

Occupancy src

Motion

CONFIGURATION 2/11

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Fan cont. heat

Default value:

Fan Control in Heating Mode

: Room Controller always controls the fan (terminal G). Valid for On or Auto fan

mode.

Off:

Fan (terminal G), when heating stages (terminals W1 & W2) are solicited, will not

be energized. The fan is controlled by the equipment fan limit control. Valid only for
Auto fan mode. On fan mode leaves the fan always on.

For multi-stage models, fan control applies to W1 & W2.

Choices

: On or Off

Fan delay

Default value:

Fan Delay

: fan mode will leave the fan always on and extends fan operation by 60 seconds

after the call for heating or cooling ends. Valid only for Auto fan mode.

Off

: fan delay not operational

Choices

: On or Off

Standby mode

Default value: Absolute

Standby Mode Configuration

Standby setpoints used for control.

Absolute

: Standby entered values are used for standby mode.

Offset:

Occupied set/- Standby diff. used for standby mode.

Choices

: Absolute or Offset

Содержание VT8600 Series

































































































Результаты поиска

Содержание VT8600 Series

Отзывы:

Похожие инструкции для VT8600 Series

Бренды по названию

Популярные бренды

Viconics VT8600 Series, Руководство пользователя интерфейса

Результаты поиска

Содержание VT8600 Series

Отзывы:

Похожие инструкции для VT8600 Series

Бренды по названию

Популярные бренды