Valley Rainger Linear Скачать руководство пользователя страница 86

Страница: 86 / 104

86 Rainger Linear

MAINTENANCE

Machine Alignment
Floating Alignment Adjustment

When a machine is equipped with floating alignment
the tower box is located on the yoke and tower box
support with a mechanical linkage between the tower
box switch pivot arm and the yoke control rod. See
Figures 86-1 and 86-2.

NOTE

• All adjustments shown are made from the

tower box side of drive unit.

1. Adjust nuts #1 and #2 as needed. Refer to Fig-

ures 86-2 and 86-3.

CAUTION

• NEVER ADJUST NUTS #1 AND #2 MORE

THAN 1/4 TURN AT ONE TIME.

• ALWAYS RE-TIGHTEN THE JAM NUTS AND

ALLOW THE TOWER TO CYCLE TWICE
(START AND STOP) TO DETERMINE IF THE
TOWER IS STILL LEADING OR TRAILING.

2. Adjust nuts #1 and #2 until the tower is in align-

ment.

3. Continue the Three Tower Method of alignment

down the entire length of the machine making
adjustments as necessary to individual towers.

Figure 86-1

Cloc

kwise

Counter-cloc

kwise

Figure 86-2

1. Nut
2. Nut

3. Yoke Control Rod
4. Switch Pivot Arm

Direction of travel

Condition

Adjust Nuts

Forward

Leading Bow

**Counter-clockwise

Trailing Bow

*Clockwise

Reverse

Leading Bow

*Clockwise

Trailing Bow

**Counter-clockwise

ADJUSTMENT CHART

Figure 86-3 * Clockwise - Adjust the nut further onto the

threaded rod.

** Counter-clockwise - Back the nut off the

threaded rod as if removing it.

Содержание Rainger Linear








































































































Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды

Valley Rainger Linear, Руководство пользователя

Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды