Valley Rainger Linear Скачать руководство пользователя страница 76

Страница: 76 / 104

76 Rainger Linear

MAINTENANCE

Swing Around Cart Lubrication

There are 10 grease fittings that must be lubricated
with a good grade of lithium based grease after every
5 passes. See Figure 76-1.
•

There are 8 grease fittings on the bearing tube
assembly.

•

There are 2 grease fittings on the swivel yoke.

Tire and Wheel
Wheel Lug Nut Torque

Wheel lug nuts should be torqued to 125 lb-ft (169.47
N·m). See Figure 76-2.
Check the wheel lug nut torque annually, preseason;
at spring start-up.

Tire Pressures

Proper tire pressure is important! Operating with low
tire pressure will damage the tires and the drive train.
Check tire pressure several times a year:
•

Pre-season: At spring start-up.

•

During-season: Check tire pressure monthly.

•

Post-season: When performing fall winterization.

For the correct tire pressure refer to the decal on the
rim or the tire pressure chart. See Figure 76-3.

WARNING

• TIRES ARE SHIPPED AT A PRESSURE OF 30

TO 35 PSI (206 TO 241 KPA).

• BE SURE THE TIRES HAVE BEEN DEFLATED

TO THE CORRECT PRESSURE (SHOWN ON
DECAL) BEFORE THE TIRE IS USED.

NOTE

• When replacing tires be sure the ply rating of

the new tire is equal to or greater than the ply
rating of the old tire.

Figure 76-1 1. Grease Fitting

2. Bearing Tube

3. Swivel Yoke

Figure 76-2 1. Wheel lug nut

Hose Drag Cart

Tire Size

Pounds per

Square Inch

Kilo pascal

(Inches)

(PSI)

(kPa)

14.9 X 24 Float Tire

124

14.9 X 24 Turf Tire

124

Span Drive Units

Tire Size

Pounds per

Square Inch

Kilo pascal

(Inches)

(PSI)

(kPa)

11.2 X 38 Tire

152

14.9 X 24 Float Tire

124

14.9 X 24 Turf Tire

124

16.9 X 24 Float Tire

16-18*

110-124

16.9 X 24 Turf Tire

16-18*

110-124

TIRE PRESSURE CHART

Figure 76-3

* Tire pressure may be reduced to 16 psi
(110 kPa) for increased flotation.

Содержание Rainger Linear








































































































Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды

Valley Rainger Linear, Руководство пользователя

Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды