manualshive.com logo in svg

Valley Rainger Linear, Руководство пользователя

Поделиться
Скачать
Valley Rainger Linear Скачать руководство пользователя страница 33

Rainger Linear   33

OPERATION

Machine Operation

The Rainger Linear was designed to be used on relatively level fields should not be used on any severe rolling or 
sloping terrain. The cart path must be maintained flat and free of any ruts or tracks which would force side loads 
into the cart frame. Should ruts develop in the cart path, the owner/operator should grade the surface smooth 
and maintain cart path flat and free of ruts or tracks during irrigation season.
For proper operation of the Rainger Linear machine, the Control Panel Owner’s Manual and Rainger Linear 
Owner’s Manual must be used together.
The Control Panel Owner’s Manual includes safety guidelines and explains the basic operation of the control 
panel itself, including how to start/stop the machine, change running direction and change water application 
amounts.
The Rainger Linear Owner’s Manual includes safety guidelines and explains the operation of the Rainger Linear 
machine including how to establish wheel tracks, methods of operation, closed delivery operation, open delivery 
operation, swing around operation, electric cord drag operation with hose and cord positioning.
All owner’s, operators and maintenance personnel MUST read and understand the Control Panel Owner’s 
Manual and the Rainger Linear Owner’s Manual.

Overwatering Timer

The overwatering timer located in the central pulse 
tower box is a safety device used to shut the machine 
off should one or both of the end towers fail to move. 
The overwatering timer is set by the operator. See 
Figure 33-1.

!

DANGER

• THE TOWER BOXES CONTAIN HIGH VOLT-

AGE! 480 VOLTS CAN KILL.

• ALWAYS DISCONNECT ELECTRICAL POW-

ER BEFORE SETTING THE OVERWATERING 
TIMER.

• ALWAYS REPLACE ANY COVER THAT WAS 

REMOVED TO MAKE OVERWATERING TIMER 
ADJUSTMENT.

Refer to the chart for suggested overwatering timer 
settings based on the control panel percent timer 
setting. The times shown in the chart are actual min-
utes that the overwatering timer will allow the central 
pulse tower box drive unit to stand still before it shuts 
the machine off. See Figure 33-2.

NOTE

• An overwatering timer setting of less than 

the Suggested Overwatering Timer Setting 
may be used when chemigating.

Each time the central pulse tower box drive unit 
moves the overwatering timer is reset and another 
time out cycle begins.

1

Figure 33-1 1. Overwatering timer

OVERWATERING TIMER SETTINGS

The overwatering timer should be set in relation-
ship to the percent timer setting.

Percent 

Timer Setting

Suggested 

Overwatering 

Timer Setting

90%

20 Minutes

80%

20 Minutes

60%

20 Minutes

40%

20 Minutes

30%

28 Minutes

10%

36 Minutes

Figure 33-2

Содержание Rainger Linear









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды