Valley Rainger Linear Скачать руководство пользователя страница 64

Страница: 64 / 104

64 Rainger Linear

OPERATION

Open Delivery
Start Up - Electric Cord / Motor Pump Applications

1. Inspect the wheel tracks to insure no vehicles or

other equipment will be contacted upon start-up
or operation.

2. If the machine has below ground guidance, turn

the oscillator ON.

3. Connect electric cord to power source. Refer to

Open Delivery Electric Cord Handling and Op-
eration beginning on page 65, then return to
this instruction and continue with step 4.

4. Check the centrifugal pump oil reservoir level.
5. Move the cart disconnect panel switch to the ON

position.

6. Move the pump panel disconnect switch to the

ON position.

7. Turn the control panel disconnect switch to the

ON position.

8. Check the voltmeter reading and verify that the

Nominal Supply Voltage is correct for this ma-
chine. See Figure 64-1.

9. Determine if the machine will be run wet or dry.

• If running the machine wet, with water:

(a) Lower suction inlet into ditch until the inlet

lift cables go slack. See Figure 64-2.

(b) Prime the centrifugal pump. See 50/60 Hz

AC Voltage Electric Primer on page 61.

After the pump is primed return to this

instruction and continue with step (c).

Refer to the appropriate Control Panel

Owner’s Manual for control panel operat-

ing procedures.

(d) Slowly fill the system with water. Slowly

open the riser valve so that the pump

does not loose prime.

(e) Refer to the appropriate Control Panel

Owner’s Manual for control panel operat-

ing procedures.

(f) Also refer to Open Delivery Electric Cord

Handling and Operation beginning on
page 67 as needed.

• If running the machine dry, without water:

(a) Make sure the suction inlet is raised out of

the ditch/water,

(b) Refer to the appropriate Control Panel

Owner’s Manual for control panel operat-

ing procedures.

Handling and Operation beginning on
page 67 as needed.

CAUTION

• DO NOT OPERATE THE MACHINE IF THE

VOLT METER READS BELOW THE MINIMUM
ALLOWED VOLTAGE OR ABOVE THE MAXI-
MUM ALLOWED VOLTAGE. SEE FIGURE 64-2.

• OPERATING THE MACHINE OUTSIDE THESE

LIMITS COULD CAUSE DAMAGE TO THE
DRIVE MOTORS AND OTHER ELECTRICAL
COMPONENTS.

• CORRECT THE LOW VOLTAGE PROBLEM

BEFORE RESUMING OPERATION.

Nominal

Supply Voltage

Maximum

Allowed Voltage

Minimum

Allowed Voltage

480 VAC @ 60Hz

505 VAC

440 VAC

415 VAC @ 50Hz

420 VAC

375 VAC

400 VAC @ 50Hz

420 VAC

365 VAC

380 VAC @ 50Hz

420 VAC

355 VAC

Figure 64-1

Figure 64-2 1. Suction Inlet

2. Ditch

3. Lift Cable

Содержание Rainger Linear








































































































Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды

Valley Rainger Linear, Руководство пользователя

Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды