Valley Rainger Linear Скачать руководство пользователя страница 55

Страница: 55 / 104

Rainger Linear 55

OPERATION

Center Inlet
Hose and Cord Positioning

6. At the machine/control panel:

(a) Set the direction of travel.
(b) Set the percentage timer to the desired application rate or speed.

7. When ready, start the machine. If applicable, start pipeline pump and open the water shut off valve for the

hose. The machine should start and run in the desired direction and stop at the end of field/hose stop post

which was set for the length of the hose.

8. If applicable, prepare the second hose by connecting the riser end to the pipeline shut off valve. Position second

hose approximately 15 ft (4.57 m) from the center of the linear cart toward the pipeline. See Figure 55-1.

9. Allow the linear cart to move past the end of the second hose approximately 50 ft (15.24 m). Stop the

machine. See Figure 55-1.

Depending on the type of center inlet do one of the
following:
•

If this is a single inlet:
(a) Close the water shut off valve for the first

hose.

(b) Select the opposite direction of travel, start

the system, and run until tension on the first

hose is relaxed. Stop the system.

shut off valve so that water from the hose

drains away from the cart path.

(d) Disconnect chains for first hose from cart

and disconnect first hose from center inlet.

(e) Connect the inlet end of second hose to the

single hose center inlet with circle lock ring.

Attach chains from the soft hose/poly hose

connection to the anchor bracket on each

side of cart.

•

If this is a double inlet:
(a) Connect the inlet end of second hose to the center inlet with circle lock ring. Attach chains from the soft

hose/poly hose connection to the anchor bracket on each side of cart. See Figure 55-2.

(b) Open the water shut off valve for the second hose and close the water shut off valve for the first hose.
(c) Disconnect the first hose from the pipeline shut off valve so that water from the hose drains away from

the cart path.

(d) Select the opposite direction of travel, start the system, and run until tension on the first hose is relaxed.

Stop the system.

(e) Disconnect chains for first hose from cart and disconnect first hose from center inlet.

Figure 55-1 1. Shut Off Valve

2. First Hose
3. Center Inlet

4. Second hose
5. Electric Cord
6. Power Pedestal

7. Alternate Power Pedestal Location and Electric Cord Position
8. Direction of Travel

Figure 55-2 1. Second Hose

2. Center Inlet
3. Circle Lock Ring

4. Chain
5. Anchor Bracket
* Double Inlet Shown

Содержание Rainger Linear








































































































Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды

Valley Rainger Linear, Руководство пользователя

Результаты поиска

Содержание Rainger Linear

Отзывы:

Похожие инструкции для Rainger Linear

Бренды по названию

Популярные бренды