manualshive.com logo in svg

Valley Rainger Linear, Руководство пользователя

Поделиться
Скачать
Valley Rainger Linear Скачать руководство пользователя страница 22

22   Rainger Linear

OVERVIEW

Standard Cart - End Feed System
Closed Delivery Hose Drag / Open Delivery Ditch Feed

If the water supply pipeline or ditch is located at the edge of the field, the four wheel cart will be the end tower 
next to the water supply pipeline or ditch. The hose drag linear cart may have a side inlet or center inlet. 
The central pulse tower box is always on the opposite end of the system from the four wheel cart. Its location 

varies depending on the total number of spans or the type of guidance system.
•  When there are 5 spans or less the central pulse tower box is located on the first tower from the end.
•  When there are 6 spans or more the central pulse tower box is located on the second tower from the end. 
•  With a Below Ground Guidance System the central pulse tower box is located on the end of free standing 

span that is furthest away from the cart.

Linear intermediate tower boxes are installed on both ends of the free-standing span.
There is no tower box on the span directly over the control panel or cart and only one end tower box located on 

the other end of the system. All other tower boxes are intermediate tower boxes. See Figure 22-1.

4

5

6

7

1

4

5

6

7

2

4

5

3

7

8

3

11

8

9

8

9

Figure 22-1 1. Above Ground Guidance

2. Furrow Guidance
3. Below Ground Guidance
4. Water Supply

5. 4-Wheel Cart
6. Free Standing Span
7. End Tower Box
8. Central Pulse Tower Box 6 or more

9. Central Pulse Tower Box -  5 or less
10.  Guidance System
11.  Antenna

Center Drive Motor RPM
Motor Type

Cart Motor RPM

Intermediate Drive Unit Motor RPM

Last Regular Drive Unit Motor RPM

Standard Speed

43

43

34

High Speed

68

68

56

Содержание Rainger Linear









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды