manualshive.com logo in svg

Valley Rainger Linear, Руководство пользователя

Поделиться
Скачать
Valley Rainger Linear Скачать руководство пользователя страница 9

SAFETY

Rainger Linear  9

Recognize Safety Information

This irrigation equipment can be powered by high voltage, which can be extremely dangerous if used improp-
erly.  For maximum safety and optimum performance of the machine, all owner/operators and maintenance 
personnel must read and understand the owner/operator manual(s), all safety messages in this manual and 
safety signs/decals on the machine before operating this equipment.
Anyone assembling, operating, servicing or maintaining this machine must read and understand all opera-
tion, maintenance, troubleshooting, testing, installation, assembly instructions and all safety messages in this 
manual before operating the machine or beginning any maintenance, troubleshooting, testing, installation or 
assembly of components.
These instructions alert you to certain things you should do carefully; if you don’t, you could hurt yourself or 
others, hurt the next person who operates the equipment, or damage the equipment.

Safety Messages

Safety messages in this manual are preceded by the hazard symbol and one of three words: DANGER, WARN-

ING or CAUTION. These messages alert you to potential hazards that could hurt you or others and or cause 

property damage.

!

   This HAZARD SYMBOL is used to alert you to information about unsafe actions or situations, and may 

be followed by the word DANGER, WARNING or CAUTION.

!

 DANGER

The HAZARD SYMBOL used with the word DANGER describes immediate hazards that can result in severe 
personal injury or death.

!

 WARNING

The HAZARD SYMBOL used with the word WARNING describes unsafe actions or situations that can result in  
severe injury, death and/or major equipment or property damage.

!

 CAUTION

The HAZARD SYMBOL used with the word CAUTION describes unsafe actions or situations that can result in 
injury, and/or minor equipment or property damage.

Information Messages

Important information messages in this manual are preceded by the word NOTE.

NOTE

The word NOTE is used to alert you to information that describes procedures or tips to help you install, operate 
or maintain your equipment properly.

Содержание Rainger Linear









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды