manualshive.com logo in svg

Valley Rainger Linear, Руководство пользователя

Поделиться
Скачать
Valley Rainger Linear Скачать руководство пользователя страница 51

Rainger Linear   51

OPERATION

Side Inlet
Hose and Cord Positioning (continued)

6.  As the machine approaches the end of field/hose stop post, Stop the machine and close the water shut off 

valve for the hose.

7.  Disconnect the first hose from the pipeline shut off valve so that water from the hose drains away from the 

cart path.
•  If more than one hose is being used, disconnect first hose from side inlet. Connect second hose to next 

pipeline shut off valve, position second hose, connect and secure to side inlet. See Figure 51-1.

•  If only one hose is being used, reposition the hose and connect to the next pipeline shutoff valve.

8.  Reposition the end of field/hose stop for the length of the hose being used. 
9.  If using the optional electric cord drag:

(a)  Make sure the power pedestal disconnect is in the OFF position.
(b)  Disconnect the electric cord from the power pedestal.
(c)  Position the electric cord far enough away from the hose, so that the hose will not drag over it. To prevent 

interference between the electric cord, cart tires and hose, bury the electric cord in the area where in-
terference will occur or when applicable, position the electric cord over the top of hose. See Figure 51-1.

(d)  Make sure the second power pedestal disconnect is in the OFF position.
(e)  Connect the electric cord to the second power pedestal.
(f)  When ready, switch the second power pedestal disconnect switch into the ON position.

10.  At the machine/control panel:

(a)  Select the original direction of travel.
(b)  Set the percentage timer to the desired application rate or speed.
(c)  If applicable set the Auto Reverse/Auto Stop control as desired.

11.  When ready, start the machine. If applicable, start pipeline pump and open the water shut off valve for the 

hose. The machine should start and run in the desired direction and auto reverse or stop at the end of field/

hose stop post which was set for the length of the hose.

12.  Repeat the steps 6-11 as needed to cross the field.

Riser

Guidance (Furrow or Cable)

Poly

14’

[4.27m]

(4”)

20’

[6.10m]

(6”)

16’

[4.88m]

(4-3/4”)

with Bumpers

Riser

Guidance (Furrow or Cable)

14’

[4.27m]

(4”)

20’

[6.10m]

(6”)

32’

[9.75m]

(8”)

16’

[4.88m]

(4-3/4”)

without Bumpers

centerline of Cart path

EOF to 1st riser = 
poly length - 50 ft.

Intermediate riser spacing = 
(2x poly length) - 80 ft.     

Intermediate

Riser

Figure 

2

5

8

1

4

7

3

6

5

10

9

Figure 51-1 1. First Hose

2. Second Hose
3. Shut Off Valve
4. Side Inlet

5. Hose Bumper (optional)
6. Electric Cord (optional)
7. Power Pedestal
8. Alternate Power Pedestal Location

9. Guidance Furrow or Cable
10.  Direction of Travel

Содержание Rainger Linear









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды