Valley Rainger Linear Скачать руководство пользователя страница 63

Страница: 63 / 104

Rainger Linear 63

OPERATION

Open Delivery

Start Up - Engine Generator Pump Applications (continued)

11. Slowly fill the system with water. Alternate be-

tween slowly opening the riser valve and increas-
ing the engine RPM so that the pump does not
loose prime.

12. Refer to the appropriate Control Panel Owner’s

Manual for control panel operating procedures.

13. When the system is running and while holding

the safety button in, move the remote shutdown
toggle switch to the enabled position. See Figure
63-1.
With the remote shutdown toggle switch in this
position the engine will stop running if the system
shuts down.

14. Check the voltmeter reading again while the gen-

erator is under load to verify that the generator is
producing the correct Nominal Supply Voltage for
this machine. See Figure 63-2.

CAUTION

• DO NOT OPERATE THE MACHINE IF THE

VOLT METER READS BELOW THE MINIMUM
ALLOWED VOLTAGE OR ABOVE THE MAXI-
MUM ALLOWED VOLTAGE. SEE FIGURE 63-2.

• OPERATING THE MACHINE OUTSIDE THESE

LIMITS COULD CAUSE DAMAGE TO THE
DRIVE MOTORS AND OTHER ELECTRICAL
COMPONENTS.

• CORRECT THE LOW VOLTAGE PROBLEM

BEFORE RESUMING OPERATION.

Figure 63-1 1. Safety Button

2. Toggle Switch

3. Engine Start Switch
4. Water Pressure Gauge Reset

Nominal

Supply Voltage

Maximum

Allowed Voltage

Minimum

Allowed Voltage

480 VAC @ 60Hz

505 VAC

440 VAC

415 VAC @ 50Hz

420 VAC

375 VAC

400 VAC @ 50Hz

420 VAC

365 VAC

380 VAC @ 50Hz

420 VAC

355 VAC

230 VAC @ 60Hz

253 VAC

220 VAC

120 VAC @ 60Hz

132 VAC

105 VAC

110 VAC @ 50Hz

121 VAC

95 VAC

Figure 63-2

Содержание Rainger Linear








































































































Результаты поиска

Содержание Rainger Linear

Отзывы:

Бренды по названию

Популярные бренды

Valley Rainger Linear, Руководство пользователя

Результаты поиска

Содержание Rainger Linear

Отзывы:

Бренды по названию

Популярные бренды