manualshive.com logo in svg

Tyco DSC PowerSeries HS2016, Справочное руководство, Страница: 49 / 130

Поделиться
Скачать
Tyco DSC PowerSeries HS2016 Скачать руководство пользователя страница 49

S e c t i o n   5 :   P r o g r a m m i n g

45

[301] Panel Events 1

1/2 – Panel AC Fail Trouble/Restore

This reporting code is transmitted when the alarm system AC supply 
fails or has been restored. A programmable delay applies to both the 
trouble and the restore. This reporting code is sent to the System 

Maintenance call direction group.

3/4 – Panel Low Battery Trouble/Restore

These reporting codes are transmitted when the panel battery voltage 
falls below 11.5VD or is restored. These reporting codes are sent to 

the System Maintenance call direction group.

5/6 – Panel Battery Absent Trouble/Restore

These reporting codes are transmitted when the panel battery voltage 
falls below 11.5VD or is restored. These reporting codes are sent to 
the System Maintenance call direction group and are transmitted 
when the panel battery is detected as absent.

[302] Panel Events 2

1/2 – Bell Circuit Trouble/Restore

This reporting code is transmitted when a bell trouble condition 
occurs or is restored on the system.This reporting code is sent to the 
System Maintenance call direction group.

3/4 – Telephone Line Trouble and Restore

This reporting code is transmitted when an alarm controller TLM 
trouble occurs or is restored. The TLM trouble is communicated over 
an unaffected communication path if available.
This reporting code is sent to the System Maintenance call direction 

group.

5/6 – Auxiliary Power Supply Trouble/Restore

This reporting code is transmitted when an auxiliary voltage supply 
trouble occurs or is restored. This reporting code is sent to the Sys-
tem Maintenance call direction group. 

NOTE: 

When the electronic fuse built in to the auxiliary power sup-

ply is tripped due to a short or high current draw, the alarm system 
must be powered down then back up to reset the fuse.

[305] Panel Events 5

3/4 – PGM 2 2-Wire Trouble/Restore

This reporting code is transmitted when a trouble condition on PGM 

2, configured as 2-wire smoke, occurs or is restored. This reporting 
code is sent to the System Maintenance call direction group. 

[311] Maintenance Events 1

1/2 – RF Jam Trouble/Restore

Sent when RF jam troubles occur/are restored. The following events 
cause RF jam troubles:

•

Wireless repeater jamming

•

RF  jam

3/4 – Fire Trouble/Restore

Sent when a low sensitivity, tamper or internal fault condition/restore 
is detected on a wireless smoke detector. 

5 – Cold Start

Sent when power is restored to the alarm system after total power 
failure. The code is sent after 2 minutes to allow the alarm controller 
to stabilize.

6 – Delinquency

When the Delinquency option is off (page 45), this code is transmit-
ted if the alarm system has not been armed for the number of days 
programmed in the Delinquency Transmission Delay (page 48). 

When the Delinquency option is on, this code is transmitted when no 
zone activity has been detected on the system for the number of hours 
programmed in Delinquency Transmission Delay.

[312] Maintenance Events 2

1/2 – Installer Lead In/ Lead Out

The Installer Lead In and Lead Out reporting codes are sent when the 
alarm system enters and exits Installer Programming respectively. 
When Installer Programming is automatically exited after PC-Link is 
activated, the Installer Lead Out event is not communicated until 

after the DLS session is complete. 

3/4 – DLS Lead In/Lead Out

The DLS Lead In reporting code is sent:
•

after DLS communication has been successfully established, but 
before the alarm system calls back the downloading computer. 
This code is only transmitted when call back is enabled

•

on user-initiated call-up. 

The DLS Lead Out reporting code is sent when a DLS session is suc-
cessfully ended.

NOTE: 

If DLS is terminated by an alarm, the DLS Lead Out report-

ing code is not transmitted.

5/6 – SA Lead In/Lead Out

The SA Lead In reporting code is sent:
•

after SA communication has been successfully established, but 
before the alarm system calls back the downloading computer. 
This code is only transmitted when call back is enabled. 

•

on user-initiated call-up. 

The SA Lead Out reporting code is sent when an SA session is suc-
cessfully ended. The SA Lead Out reporting code is still sent if the 

session is terminated by an alarm.

7 Event Buffer 75% Full 

Sent when the event buffer reaches a threshold of 75% without being 
uploaded.

[313] Maintenance Events 3

1/2 – Firmware Update Begin/was Successful

Sent when a remote firmware update is initiated/ is successfully com-

pleted.

3 – Firmware Update Fail

Sent after an unsuccessful remote firmware update.

[314] Maintenance Events 4

1/2 – Gas Trouble/Restore

3/4 – Heat Trouble/Restore

5/6 – Freeze Trouble/Restore

7/8 – Probe Disconnected Trouble/Restore

[321] Receiver Events

2/4/6/8 – Receiver 1 - 4 FTC Restore

Sent when the panel detects an FTC trouble.

[331] Module Events 1

1/2 – Module AC Trouble/Restore

This reporting code is transmitted when a module’s AC supply fails 
or has been restored. A programmable delay applies to both the trou-

ble and the restore. This reporting code is sent to the System Mainte-
nance call direction group.

firealarmresources.com

Содержание DSC PowerSeries HS2016



































































































































Отзывы:

Нет отзывов