Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 79 / 122

V-1

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Chapter V

Analyzer Maintenance

The Thermo Scientific Orion 2117HL chloride analyzer is designed for

simple maintenance. Follow the instructions in this section to ensure

proper operation of your analyzer.

To ensure proper maintenance and good analyzer performance, a service

logbook should be kept.

• Record maintenance date and the type of service work completed.

• Tag each electrode cable with the installation date of the electrode.

1. Check that the sample flow rate is 35 to 45 mL/minute. To alter

the flow rate, pull out the locking knob of the pressure regulator,

then rotate the black knob to increase (clockwise) or decrease

(counterclockwise) sample flow. Push in the locking knob of the

pressure regulator to lock the flow rate.

2. Inspect the analyzer for leakage.

3. Check that there are no error indications and that the current

concentration level is reasonable.

4. Check that the reference filling solution is adequate.

5. If required, wipe the analyzer with a damp cloth to remove dirt and

dust particles.

Maintenance Schedule

Weekly Maintenance

Recommendations

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды