Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 71 / 122

Calibration

IV-9

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Step

Operator Action

Scrolling Marquee

Main Display

Notes

Press

to accept the new slope and

values

or
Press

to abort the calibration. The

new slope and E

values will not be saved.

The last saved calibration prior to the
aborted calibration will be used in the
measure mode.

NEW CALIBRATION SLOPE AND E

PRESS ENTER TO ACCEPT OR PRESS

EXIT TO ABORT WITHOUT SAVING

Calculated Slope

and E

is pressed,

refer to the

Calibration Abort

Steps

section.

Pull the diverter valve out.
Turn the inlet valve on.
Close the calibration port on
the flow cell cap.

PULL DIVERTER VALVE OUT
TURN INLET VALVE ON
CLOSE CAL PORT
PRESS ENTER

FLO On

Press

PULL DIVERTER VALVE OUT
TURN INLET VALVE ON
CLOSE CAL PORT
PRESS ENTER

FLO On

System will proceed to measure mode.

Actual temperature reading

Actual concentration

reading

System enters

measure mode, but

will remain on hold

until the hold timer

expires. Default hold

time is 30 minutes.

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды