Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 72 / 122

Calibration

IV-10

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Step

Operator Action

Scrolling Marquee

Main Display

Notes

Calibration Abort Exit Steps –

is pressed at any point during the calibration, proceed with the following steps

Exit 1

ARE YOU SURE?
PRESS ENTER TO ABORT OR PRESS

LAST SCREEN TO BACKUP

SUrE
?

Exit 2

Press

to abort the calibration.

or
Press

to return to the last screen

used in the calibration sequence prior to
when

was pressed. Continue to

follow the calibration steps according to
the marquee and main display directions.

ARE YOU SURE?
PRESS ENTER TO ABORT OR PRESS

LAST SCREEN TO BACKUP

SUrE
?

Exit 3

CALIBRATION ABORTED
PRESS ENTER

CAL
Abrt

Exit 4

Press

to abort the calibration.

CALIBRATION ABORTED
PRESS ENTER

CAL
Abrt

Exit 5

Pull the diverter valve out.
Turn the inlet valve on.
Close the calibration port on the
flow cell cap.

PULL DIVERTER VALVE OUT
TURN INLET VALVE ON
CLOSE CAL PORT
PRESS ENTER

FLO On

Exit 6

Press

PULL DIVERTER VALVE OUT
TURN INLET VALVE ON
CLOSE CAL PORT
PRESS ENTER

FLO On

Exit 7

No operator action needed.
The system will enter the measure mode
and remain on hold until the hold timer
expires (default hold time is 30 minutes).

Actual temperature reading

Actual concentration

reading

The system allows the operator to abort the calibration or return to the

calibration when

is pressed at any point during the calibration.

The following table lists the calibration abort steps with their marquee

display and required operator actions.

Calibration

Abort Steps

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды