Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 100 / 122

Troubleshooting

VI-17

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

The Thermo Scientific Orion 2117HL chloride analyzer allows the user to

reset the analyzer through the setup mode or by a hard reset. Resetting the

analyzer will restore all settings in the setup mode to factory default values.

Warning:

Resetting the analyzer will erase all data logs including

calibration, and password protection settings for setup and calibration.

The analyzer will reset setup parameters to factory default settings.

Operator Action

Scrolling

Marquee

Main

Display

Notes

Press

in the measure mode

to enter the setup mode

Last menu used

in setup mode

SEL
SCrn

SETUP appears

as mode

Press

until RSET

appears in the marquee

RSET
(flashing)

SEL
SCrn

Press

to reset the analyzer

PRESS TEST

VIEW ENTER TO

RESET

rSEt
?

Press

When the reset is complete, the
system will return to the measure
mode. The operator will need
to re-enter the setup mode to
continue programming the setup
parameters. Press

to return

to the setup mode.

PRESS TEST

VIEW ENTER TO

RESET

rSEt
?

This command

resets all

previously set

parameters to

factory default

values. Use this

command only to

set the analyzer

to original

factory setup

values.

Resetting the

Analyzer

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды