Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 30 / 122

Analyzer Operation

III-4

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

The default password is 0000 – indicates password protection has not

been activated.

System password:

Management secured password protection of setup

mode and calibration process.

Calibration password:

Operator secured password for protection of

calibration process only.

If password(s) are activated:

•  System prompts operator to enter system password:
•  Marquee: ENTER PASSWORD
•  Main display top: PASS
•  Main display bottom: 0000 (flashing)
•  Correct password – Allows operator to enter setup mode for custom

programming options.

• Incorrect password – Password incorrect or not entered correctly.
• System password:

• Marquee: SYSTEM PASS INCORRECT
• Main display: E035

• Calibration password:

• Marquee: CAL PASS INCORRECT
• Main display: E034

• Verify password and re-enter it.

If password(s) are de-activated:

• System enters the setup mode at the last setup menu option used by

the operator.

• Marquee: Flashes current menu option
• Main display: SEL SCrn

Using Password

Protection

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды