Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 42 / 122

Analyzer Operation

III-16

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Warning:

The reset command will erase all operator settings, logs and calibration data. The analyzer will

need to be set up and calibrated again before it can resume operation.

Default

Operator Action

Scrolling Marquee

Main Display

Notes

RSET

RSET
(flashing)

SEL
SCrn

Press

to reset the analyzer

PUSH TEST VIEW ENTER

TO RESET

rSEt
?

To Reset the Analyzer:

Press

When the reset is complete, the system
will return to the measure mode. The
operator will need to re-enter the setup
mode to continue programming the setup
parameters. Press

to return to the

setup mode.

PUSH TEST VIEW ENTER

TO RESET

rSEt
?

This command resets

all previously set

parameters to factory

default values. Use

this command only

to set the analyzer to

original factory setup

values.

To Abort the Reset:

Press

to return to the main

setup mode

PRESS TEST VIEW ENTER

TO RESET

rSEt
?

RSET
(flashing)

SEL
SCrn

Press

to scroll to the next menu

Warning:

Resetting the analyzer will erase all stored information including relay, logs and

calibration settings.

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды