Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 25 / 122

Analyzer Preparation

II-12

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Danger:

Turn off the air pump prior to removing the reference electrode

filling solution bottle. If the air pump is left on, it will spatter filling

solution as the bottle is removed.

1. Unpack the reference electrode (Cat. No. 100057) and its instruction

sheet from the shipping box.

2. Carefully remove the protective caps from the bottom and sidearm of

the reference electrode. Save the caps for future storage of the electrode.

3. Shake out as much of the filling solution as possible through the

sidearm. Drain the fill solution through the sidearm or use a pipet

or syringe.

4. While passing the 1/8 inch tubing into electrode sidearm, slide the 1/4

inch tubing over the sidearm. The outside tubing should extend 3/8 to

1/2 inches over sidearm. Refer to

Figure II-9

5. Remove the cap and fluid seal from reference electrode fill solution

bottle (Cat. No. 100057F4). Hold the bottle in an upright position.

Check that the rubber gasket is properly aligned, and then connect

the cap end of the tubing assembly to the bottle. The 1/8 inch tubing

should extend into the bottle.

6. Hold the reservoir bottle above the electrode with the bottle cap end

down. The electrode should be horizontal with the sidearm pointing

up. Gently shake the electrode to allow any trapped air bubbles to rise

into the bottle as the electrode fills with solution.

Installation of a New

Reference Electrode

Reference Electrode

Filling Solution

Gasket

Tubing Bottle Adaptor

Small 1/8” Tubing Inside

Bottle Cap

Large 1/4” Tubing

Electrode Sidearm

Ceramic Frit

Figure II-9

Reference Electrode

with Filling Solution

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды