Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 80 / 122

Analyzer Maintenance

V-2

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Calibration frequency is operator dependent for the most accurate and

precise measurements.

• Refer to

Chapter IV, Performing a DKA Calibration

• Calibration intervals can be programmed using the setup mode. This

will prompt the operator to recalibrate after a specific amount of time

has passed. Refer to

Chapter III, Use of the Setup Mode

Refer to

Chapter II, Installation of a New Reference Electrode

Reference electrode filling solution is meant to be a several month supply.

Therefore, if the filling solution bottle is less than one quarter full, replace

the solution. This should be checked each month to ensure that the

electrode does not run dry.

Danger:

Turn off the air pump prior to removing the reference electrode

filling solution bottle. If the air pump is left on, it will spatter filling

solution as the bottle is removed.

1. Turn off the air pump. Refer to

Chapter III Shutdown and

Start-Up Procedure

2. Remove the hollow push pin on the discharge tube of the air pump

from the base of the filling solution bottle.

3. Remove the filling solution bottle from the clip. Unscrew the cap and

discard the bottle.

4. Remove the cap and seal from a new reference electrode filling solution

bottle. Check that the rubber gasket is properly aligned, and then

connect the cap and tubing assembly to the bottle. The 1/8” tubing

should extend into the bottle.

5. Invert the filling solution bottle and snap it into the clip.

6. Puncture the base of the filling solution bottle with the hollow push pin

on the discharge tube of the air pump. Push the pin down until its

PVC base abuts the bottle. Mark and date the level of filling solution

in the reservoir. The electrolyte solution will begin to flow into the

reference electrode.

Calibration

Monthly Maintenance

Replacement of Reference

Electrode Filling Solution

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды