Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 83 / 122

Analyzer Maintenance

V-5

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Use the restrictor tube assembly (Cat. No. 2100RT). Refer to

Figure V-2

for the restrictor tubing connections.

1. Close the inlet valve to stop sample flow through the analyzer.

2. Loosen the restrictor tube fitting connection from the top of the

flow meter.

3. Loosen the restrictor tube fitting from the left side of the flow

cell block.

4. Pull out the restrictor tube assembly at each end.

5. Unscrew the clip behind flow cell that holds the restrictor tube to

the panel.

6. Replace with a new restrictor tubing assembly.

7. Be sure all of the fittings are secure, to prevent leaks.

8. Open the inlet valve to start sample flow through the analyzer.

Replacement of

Restrictor Tubing

Figure V-2

Restrictor Tubing

restrictor

adapter

restrictor

tube assembly

clamp

fitting

flow

meter

O-ring

to check valve on

flow cell manifold

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды