Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 16 / 122

Analyzer Preparation

II-3

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Sample Requirements

Additional information is listed in the

Appendix, Specifications

section.

Sample inlet connection –

1/4” NPTF. If particulate matter is present in

the sample, pre-filtration is necessary. The 60 micron stainless steel filter

located after inlet valve will remove moderate amounts of particulates.

Flow rate –

40 mL/minute (nominal).

Pressure –

8 to 100 psig. Consult Technical Support for details on sample

handling if the pressure is outside of this range.

Temperature –

Temperature must be between 5 and 35 °C.

Chloride level –

Chloride levels are read directly in ppb or ppm, when

calibrated with Thermo Scientific Orion 29,600 ppm high level chloride

standard.

Sample alkalinity –

Sample alkalinity should be less than 50 ppm CaCO

equivalent. For higher sample alkalinity, contact Technical Support.

Sulfite –

Sulfite cannot be present in the sample.

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды