Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 91 / 122

Troubleshooting

VI-8

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

• The main display will show

and the marquee will display

KEYPAD

TEST PRESS ALL KEYS ONE AT A TIME

• Press all eight keys one at a time in any order.

* After the first key is pressed Error E033 will be displayed if a new key is

not pressed within 10 seconds.

Keypad Test

Default

Operator Action

Scrolling Marquee

Main Display

Notes

Keypad Test

KEYPAD TEST
PRESS ALL KEYS ONE AT A TIME

Press all keys one at a time in any order

KEYPAD TEST
PRESS ALL KEYS ONE AT A TIME

Display will show

numbers 1 through 8

as keys are pressed

After the first

key is pressed

error E033 will

be displayed

if a new key

is not pressed

within 10

seconds

No operator action needed
The system will enter the measure mode
if the keypad test is passed

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды