Thermo Scientific Orion 2117HL Скачать руководство пользователя

Страница: 73 / 122

Calibration

IV-11

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Error

Operator Action

Scrolling Marquee

Main Display

Notes

Stability Time Out Error

Error

Press

to continue the calibration

despite the reading instability.
or
Press

to abort the calibration and

refer to Exit 3. Repeat the calibration or
refer to the troubleshooting section.

READINGS WERE UNSTABLE
PRESS ENTER TO CONTINUE

CALIBRATION OR PRESS EXIT

TO ABORT

E041

The required system

stability was not

reached and a time

out error occurred.
Perform electrode

cleaning, conditioning

and troubleshooting.

Calibration Errors

Error

Press

to abort the calibration and

refer to Exit 3.
Verify that the correct standards were
used during the calibration, the standard
values were entered correctly and in the
right order and the electrodes are working
properly and then repeat the calibration.

INVALID SLOPE
PRESS ENTER

E042

The calculated slope

was invalid.
Standard values were

likely entered in the

wrong sequence

or wrong standard

values were entered.

Error

107

Press

to abort the calibration and

refer to Exit 3.

CALIBRATION DATA TOO

CLOSE TOGETHER
PRESS ENTER

E107

Use new standards.
Perform electrode

cleaning, conditioning

and troubleshooting.

Error

109

Press

to continue the calibration

despite the bad slope.
or
Press

to abort the calibration and

refer to Exit 3.

CH1 BAD SLOPE
PRESS ENTER

E109

The calculated slope

was outside of the

recommended range.
Perform electrode

cleaning and

conditioning, refer to

the troubleshooting

section and repeat the

calibration.

At any point during a calibration, the appropriate error message will be

displayed if there is a calibration related error.

The following table lists common calibration error codes with their

marquee display and required operator actions.

Calibration

Error Codes

Содержание Orion 2117HL



























































































































Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2117HL, Руководство пользователя

Результаты поиска

Содержание Orion 2117HL

Отзывы:

Похожие инструкции для Orion 2117HL

Бренды по названию

Популярные бренды