Thermo Scientific 42iQD Скачать руководство пользователя страница 84

Страница: 84 / 286

Operation

Settings

3-60

42iQD Instruction Manual

Thermo Scientific

The Preventive Maintenance screen reminds the user when certain

instrument components need to be serviced/replaced. When the “Months

Left” has decreased to 2, the row is highlighted yellow. If the “Months

Left” is 1 or less, the row is highlighted red and the maintenance icon

(gears) will appear in the status bar located at the bottom of the screen.
Use the



and



buttons to move up and down and the



and



buttons to move left and right.

Home Screen>Settings>Health Check>Maintenance>Preventive

Maintenance

The Preventive Maintenance screen contains the following information:

●

Across:

●

Component:

Device to be routinely serviced or replaced.

●

Interval in Months:

Expected period of time before a component

needs to be checked and/or serviced.

●

Months Left:

Count down timer in months. Remaining time since

the beginning of the service interval. When the value is 1 or less,

the row will be highlighted and it is suggested that the component

should be checked and/or serviced.

●

Reset:

Once the component is serviced/replaced, the user presses the

Reset button and the “Months Left” value resets to the “Interval in

Months” value.

●

Alert:

Allows the user to opt out of receiving preventive

maintenance alerts. Displays Enabled/Disabled for each

component.

Preventive Maintenance

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды