Thermo Scientific 42iQD Скачать руководство пользователя страница 267

Страница: 267 / 286

Safety, Warranty, and WEEE

Warranty

Thermo Scientific

42iQD Instruction Manual

A-3

prevailing time and materials rates. If Seller provides repair services or

replacement parts that are not covered by the warranty provided in this

warranty, Buyer shall pay Seller therefor at Seller's then prevailing time and

materials rates. ANY INSTALLATION, MAINTENANCE, REPAIR,

SERVICE, RELOCATION OR ALTERATION TO OR OF, OR

OTHER TAMPERING WITH, THE PRODUCTS PERFORMED BY

ANY PERSON OR ENTITY OTHER THAN SELLER WITHOUT

SELLER'S PRIOR WRITTEN APPROVAL, OR ANY USE OF

REPLACEMENT PARTS NOT SUPPLIED BY SELLER, SHALL

IMMEDIATELY VOID AND CANCEL ALL WARRANTIES WITH

RESPECT TO THE AFFECTED PRODUCTS.
THE OBLIGATIONS CREATED BY THIS WARRANTY

STATEMENT TO REPAIR OR REPLACE A DEFECTIVE PRODUCT

SHALL BE THE SOLE REMEDY OF BUYER IN THE EVENT OF A

DEFECTIVE PRODUCT. EXCEPT AS EXPRESSLY PROVIDED IN

THIS WARRANTY STATEMENT, SELLER DISCLAIMS ALL

OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ORAL

OR WRITTEN, WITH RESPECT TO THE PRODUCTS,

INCLUDING WITHOUT LIMITATION ALL IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY

PARTICULAR PURPOSE. SELLER DOES NOT WARRANT THAT

THE PRODUCTS ARE ERROR-FREE OR WILL ACCOMPLISH

ANY PARTICULAR RESULT.

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды