Thermo Scientific 42iQD Скачать руководство пользователя страница 41

Страница: 41 / 286

Operation

Calibration

Thermo Scientific

42iQD Instruction Manual

3-17

●

Schedule Averaging Time:

Allows the user to adjust the zero/span

schedule averaging time. This averaging time only affects the zero/span

schedule.

●

Background Calibration:

Toggles Enabled/Disabled. If enabled,

background value is calibrated. If disabled, schedule runs a background

check only and background value is not updated.

●

Span Calibration:

Toggles Enabled/Disabled. If enabled, span

coefficient is calibrated. If disabled, schedule runs a calibration check

only and span coefficient is not updated.

●

Zero : Span Ratio:

Allows the user to perform more scheduled

background calibration checks to span calibration checks. Default is 1

and therefore reads 1:1. (This means that each time the schedule is run,

both the zero duration and span duration occurs.) The zero/span ratio

is allowable between 1 to 99. If 99 is chosen, the schedule should only

perform the Span on the 99th iteration.

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды